Disclosure: This post contains affiliate links. If you buy through them, Built & Backyard may earn a commission at no extra cost to you.
Quick answer
Weatherstripping is the cheapest comfort upgrade you can make: about $30–$100 in materials seals most of a house’s doors and windows in one afternoon. Do it in this order — exterior doors (including the door sweep), the garage door bottom and perimeter, then windows. Match the seal to the gap: V-strip or kerf foam for door sides and tops, a sweep for the bottom, a bottom seal + perimeter seal for the garage door, and foam tape or a shrink-film kit for windows. ENERGY STAR estimates that sealing air leaks (with insulation) saves about 15% on heating and cooling costs — and the rooms simply feel warmer at the same thermostat setting.
First: find the drafts
Don’t guess. On a cold or windy day:
- Hand test: Run your palm slowly around door and window frames. Moving air is obvious.
- Paper test: Close a dollar bill in the door at several points. If it slides out with no drag, the seal at that spot is gone.
- Smoke test: Hold a lit incense stick near edges and watch where the smoke wavers (turn off the furnace fan first). This finds leaks you’d never feel.
Mark each bad spot with painter’s tape so your shopping list matches reality.
Where the air actually leaks
Doors and windows get the blame, but they’re only part of the picture in a typical home:
| Leak location | Approx. share of air leakage |
|---|---|
| Floors, walls, ceilings (attic) | ~31% |
| Plumbing/electrical/HVAC penetrations | ~17% |
| Ducts | ~15% |
| Fireplace | ~14% |
| Doors | ~11% |
| Windows | ~10% |
Translation: weatherstrip the doors and windows because it’s fast and cheap — then look up. The attic hatch and penetrations are where the big losses hide (our garage insulation guide covers the same principle for the garage).
The main types, and where each one wins
| Type | Best for | Lifespan | Notes |
|---|---|---|---|
| V-strip (plastic/metal) | Door/window sides & tops | 5+ years | Springs open to fill the gap; nearly invisible |
| Kerf foam (door-slot) | Pre-grooved door frames | 3–5 years | Presses into the slot around modern doors; no glue |
| Foam tape (self-stick) | Irregular gaps, windows | 1–3 years | Cheapest and easiest; compresses flat over time |
| EPDM rubber tape | Doors that close flat on a stop | 5+ years | Seals well down to very cold temps; install at 40–90°F |
| Door sweep | Bottom of exterior doors | 5+ years | The single biggest door draft is usually underneath |
| Garage door bottom seal | Bottom of garage door | 3–5 years | Rubber U/V channel; also keeps out water and mice |
| Shrink-film window kit | Windows that stay shut all winter | One season | Remarkably effective on old, leaky windows |
How to seal each spot
Exterior door, sides and top (30 minutes): Pull the old stripping out of the kerf slot (or off the stop). Press in new kerf foam — no tools beyond scissors — or stick EPDM tape on the stop where the door face lands. The door should close with slight resistance and pass the paper test all the way around.
Exterior door, bottom (20 minutes): Daylight under the door means a worn sweep or threshold. Most sweeps unscrew from the inside face; swap in the new one, adjust so the fins just kiss the threshold, done.
Garage door (1 hour): Two separate jobs. The bottom seal slides or presses into the retainer channel across the door’s bottom edge — pull the old rubber out, feed the new one in with soapy water as lubricant. The perimeter seal (vinyl flap on a rigid strip) nails to the frame so the flap presses against the door face on the top and sides. Together they stop the whistle, the dust, and most of the water that creeps under the door. This is Step 2 of sealing a garage for heat — pair it with the sizing numbers in our garage heater guide and you’ll feel the difference the first cold night.
Windows (10 minutes each): Foam tape on the sash edges for windows you still open. For windows that stay shut until spring, a shrink-film kit (tape + film + hair dryer) honestly outperforms most permanent fixes on old double-hungs.
Our picks
Best for the garage door: M-D Building Products Garage Door Bottom Seal
Heavy-duty rubber seal that fits standard retainer channels, stays flexible in the cold, and closes the gap that lets in drafts, water, and critters. Measure your door width and channel type before ordering.
→ Check price on Amazon
Best all-rounder for doors: Frost King V-Seal Weatherstrip
The classic V-strip: folds into a springy seal for door and window sides/tops, lasts for years, and can even be applied in colder weather than foam tapes (rated down to about 20°F). One roll handles a couple of doors.
→ Check price on Amazon
Best for leaky windows: Duck Brand Max Strength Window Insulation Kit
Shrink-film kit with film twice as thick as standard kits; covers up to five windows. On old single-pane or rattly double-hung windows, this is the biggest comfort gain per dollar on this page.
→ Check price on Amazon
5 mistakes that ruin a sealing job
- Installing tape on dirty or cold surfaces. Adhesive fails below ~40°F and on dusty paint. Clean with alcohol, warm the strip indoors, and it sticks for years.
- Sealing over the old, dead stripping. Compressed foam seals nothing. Pull the old stuff first.
- Too thick a seal. If the door needs shoulder pressure to latch, the seal is oversized — it’ll tear itself apart and strain the hinges.
- Forgetting the door bottom. Sides and top get all the attention; the under-door gap is usually the largest single opening.
- Sealing vents and combustion air. Never block the air supply or flues for a furnace, water heater, or fireplace, and keep working CO alarms in the house. A tighter house is the goal — a sealed-tight one with gas appliances needs a tech’s venting check.
FAQ
How much does weatherstripping save, really?
ENERGY STAR pegs air sealing plus insulation at roughly 15% of heating and cooling costs (about 11% of the total energy bill), and DOE estimates draft reduction alone can cut home energy use 5–30% depending on how leaky the house was. Doors and windows are the easy slice of that.
When is the best time to install it?
A mild fall day — exactly now. Most adhesive products want 40–90°F surfaces. V-strip and nail-on products are more forgiving of cold.
How long does weatherstripping last?
Foam tape: 1–3 years. Kerf foam and EPDM: 3–5+. V-strip and sweeps: 5+ years. Check the paper test every fall and replace only what’s failed.
Should I weatherstrip before insulating or buying a heater?
Seal first — it’s the cheapest step and it makes everything after it work better. Then insulate, then size the heater to the tightened space.
Renting or can’t modify the door?
Removable options exist: rope caulk and removable sealant for window gaps, and fabric draft stoppers for under doors. Not as good, but far better than a towel.
This guide completes the fall garage series — seal the drafts here, then insulate and size your heater right.
